Installation Guide for Dodge Charger LED Rear Seat Front Map lights

And here is exactly what you may need:
Regarding the Chargers, you will probably need the following light bulbs.
(2) 44mm rigid loop, 9 LED Festoon light bulb (front map lamps)
(2) 194 SMT tower LED (rear seat map lighting)
(1) 44mm rigid loop, 9 LED Festoon light (rear trunk light)
(1) 194 4-star SMT (rear exterior license plate light)

There's no courtesy lights and glove box lights for the Dodge's. Although you can get the glove box lighting and install in your glove box.
And then you will require a: (1) 194 SMT tower LED (glove box)

Rear seat map lighting (similar to the front map lights)

1. From the click on/off end of the clear lens. Work with a tiny jewelry/glasses flat head screw driver. Carefully wedge it into the on/off end of the lens and pry that end of the lens down. It may possibly seem like it will take, don't be concerned. The other end of the lens has a tab on it and basically pull the lens, soon after popping it from the on/off end and it will appear.

2. You need to right now see the oem 194 bulb and a rear reflector.

3. I work with the smaller flat go to pop the 194 bulb out. I own a towel in the other hand to catch the hot 194 LED bulbs.

4. Never take away the rear reflector on the rear map lighting.

5. Before the installation of the 194 tower SMT lamps. Check out the socket prongs that keep the light bulb in place. While you take away the oem 194 light bulbs, the prongs usually tend to un-bend a little. So get your fingers and casually re-squeeze them a bit stronger.

6. Once the fresh 194 LED is fitted. Flick it a few times to make sure it keep on. If it doesn't. Move the led bulb out and re-squeeze the socket prongs. When the light stays on. Re-mount the clear lens.

7. Have the end of the lens by using the wedge on it and put that directly into place. After that push in the on/off click end and you are completed.

We found this useful information from chargerforums.com and to shop LED bulbs, please visit us at www.LEDoption.com, the cheap LED bulbs store.

Installation Guide for Dodge Charger LED Front Map Lights

Here's just what you'll require:
For the particular Chargers, you may need the following light bulbs.
(2) 44mm rigid loop, 9 LED Festoon bulb (front map lighting)
(2) 194 SMT tower LED (rear seat map lighting)
(1) 44mm rigid loop, 9 LED Festoon bulb (rear trunk light)
(1) 194 4-star SMT (rear exterior license plate light)

You can find no courtesy lights and glove box lamps for the Dodge's. Nonetheless you can buy the glove box light and install in your glove box.
Then you will need a: (1) 194 SMT tower LED (glove box)

Putting in the lamps.

Front Map Lights.
1. From the click on/off end of the clear lens. Use a tiny jewelry/glasses flat head screw driver. Very carefully wedge it into the on/off end of the lens and pry that end of the lens straight down. It may seem such as it will snap, don't worry. The backside end of the lens is held in place by 2 notches. Pull down with your fingers and it should pop free. Occasionally it pops free when you are wedged in having the flat head and taking down.

2. Remove the rectangular metal reflector. I use a set of pliers, simply because the metal may be hot. You will certainly be left with the oem light bulb and the rear refector, at the rear of the lamp.

3. I work with a small hand towel to attain up and get rid of the oem light bulb, it will be very hot.

4. Consider your pliers and acquire a grip on the rear reflector piece, nearest to the roof. You will really need to pull and twist to get the rear reflector to pop off of its 2 moutning points. At this point. You might throw away each metal reflectors, you will probably not need all those.

5. Before fitting the 44mm LED bulbs. Head to the socket prongs that hold the bulb in place. As soon as you remove the oem lamp, the prongs are likely to un-bend a little. So consider your fingers and lightly re-squeeze them a bit stronger. And then pop in your LED lamp and rotate it until all the 9 led lights are attempting straight down. You can put your hand under the lighting to support discover where it's aiming.

6. Get the clear lens and line it up with the 2 notches in back. Take all those directly into place. Next pop the click on/off end again up into place.

We found this useful information from chargerforums.com and to shop LED bulbs, please visit us at www.LEDoption.com, the discount LED bulbs store.

LEDoption BA9 High Power H6W 64111 3886X 1895 LED Bulbs Reviews

Producing LEDoption.com's 1W BA9 bayonet High Power LED light bulbs. This type of BA9 bayonet LED light bulbs are available in the following colors: Xenon White and Ultra Blue.

A light-emitting diode (LED) is a semiconductor light source which is frequently used for automotive for example on Audi for daytime running lights, BMW for LED tail lights and Lexus for LED license plate lights; as well broadly presents itself on electronics such as cell phone for background lighting, flash lighting, even household for instance present panels and Television. Total, the most places the LEDs are used as a brand-new lighting source to upgrade the common incandescent lights and halogen light bulbs.

High power light-emitting diodes (LEDs) are likely to change other technologies such as incandescent and fluorescent lamps in signaling, solid state lighting, and car headlights because they spend less electricity and increase the light's time. LEDs lights are everywhere from 500 milliwatts to 10 watts. A few of the electricity in an LED becomes heat rather than light. If the heat is not taken away, the LEDs work at high temperatures, which not simply lowers their efficiency, but also would make the LED extra unsafe and fewer dependable. Thus, thermal operations of high power LEDs is a crucial area of exploration and development.

You'll find numerous various sort of High Power BA9 LED chips on the current market such as 64111, H6W, 1895, 53, 57, 182, 3886X, the mathematical numbers are mainly measurement of the dimensions of the High Power LED size by millimeter.

This particular type of BA9 LED light bulbs are High Power LED lights on the top. The dimensions of this LED bulb is measured at 0. 56" for diameter and 1. 09" for length.

General speaking, this form of BA9s Bayonet LED light lamps can exchange 64111, H6W, 1895, 53, 57, 182, 3886X, BA9, BA9s light lamps.

Below are the pictures exhibiting all two colors we have for this sort of High Power BA9 64111 LED, you can click on the LED bulb image to enlarge.

Thanks to DONSBULBS for the technical specs for this BA9 Bayonet style bulb.

The stock BA9s bulbs' voltage is 12V, with current is measured at 0. 417 AMP with full wattage at 5W. As a result of this light is at 5W, for that reason it is as well known as H5W. The average life for the incandescent BA9s bulb is 200 operating hours, but our BA9 LED bulbs in comparison has life-span varying from 2, 000 to 20, 000 working hours.

　

　

For more information about BA9 LED bulbs and 64111 LED bulbs, please visit our website LEDoption.com

LED Tail Lights and Resistor Installation for Chevrolet

Just before

Tail light removing... There are two phillips head screws per tail light to take out

... As soon as these are out pull the tail light out. You will need to use a bit of persuasion still but they should come on out

Following, the harness connects just under the auto..

... simply detach the harness and your good. Watch out for dropping debris!!!

At this issue the previous tail light is out there and you're prepared to install the fresh assembly. For the most component the tail light will just plug in and you're good to go. I've seen that THE MAJORITY OF people have no issue with the hyper blink on these G4's on the other hand there are a handful that have had the matter so I just make the resistor mod from the get go with the hopes of not having to handle it afterwards so ahead of putting in the lighting I spliced in the brand new resistor.

Primary, cut the wires on the first, gray common box that will come with the lighting.

Up coming you'll prefer to splice in the brand-new resistor. In addition, this is just a short-term splice for now. This weekend I plan on getting a few get smaller connectors to keep it free from the weather. You'll additionally want to zip tie your wires up in a bundle to keep these arranged and out of the way (not pictured)...

... from my study it doesn't matter which end go to the green wire and which end goes to the black wire. This resistor did are available with Scotch-lok connectors but I opted not to use them (and various folks urged me to trash them as well)

Obtaining the resistor is simple. I used the red 3M tape (very strong stuff!! )

... and put it on the back and connected the resistor to the back of the tail

Did my tests (lights, brakes, blinker,... )

Just for grins here's a picture of one LED in and one stocker in. HUGE difference IMO

Do these exact steps to the other aspect and...

Sorry for the crappy cell photographs but it was just less complicated. In addition, I was planning to do this out in the light to get greater pics but it's been so rainy I was too impatient to wait longer just before I mounted them.

We found this useful information from tahoeyukonforum.com and to buy car LED bulbs, please visit us at www.LEDoption.com, the discount LED bulbs store.

Introducing LEDoption T5 5050-SMD 24 27 73 74 LED Bulbs

Producing the LEDoption.com's 1 piece 5050 SMD shine T5 LED light bulbs on the top. This kind of 1 piece 5050 SMD shine T5 LED light bulbs are available in the following colors: Xenon White and Ultra Blue.

A light-emitting diode (LED) is a semiconductor light source which is frequently used for automotive for example on Audi for daytime running lights, BMW for LED tail lights and Lexus for LED license plate lights; in addition broadly seems on electronics such as cell phone for background lighting, flash lighting, even household for instance show panels and Tv set. Total, the the majority of places the LEDs are used as a brand-new lighting source to change the traditional incandescent lamps and halogen light bulbs.

Surface mount technology (SMT) is a method for setting up digital circuits in which the components (surface-mounted components/devices) are attached directly onto the surface of printed circuit boards (PCBs). An electronic device so made is called a surface mount device (SMD). By using this style of SMD technology for LED lights makes it probable to possess a lot of different types of designs, configurations, etc.

There are numerous different type of SMD LED chips on the current market like 5050 SMD, 1210 (3528) SMD, 0603 SMD and 3020 SMD, the mathematical numbers are basically measurement of the dimensions of the SMD LED measurement by millimeter.

This unique type of T5 LED bulb has 1 piece 5050 type SMD LED light on the top makes this kind of shinning T5 LED bulb that will create a excellent bright and cool color. The measurement of this LED bulb is measured at 0. 25" for diameter and 0. 7" for length.

General speaking, this sort of T5 LED bulbs can change 24 27 73 74 2721 filament light bulbs, and will also exchange the following light bulbs: 17 18 37 58 70 79 85 86.

Below are the photos displaying all two colors we have for this form of T5 5050 SMD LED bulbs, you can click on the T5 24 LED bulbs image to enlarge.

 

 

Ultimately, there is some data concerning the stock 24 type incandescent light bulbs, thanks for DONSBULBS for the features.

The stock 24 bulbs' voltage is 14V, with present is measured at 0. 243 AMP with total wattage at 3. 4W. The size of the base is 5mm, therefore it is commonly called as T5 bulb. The ordinary life-span for the 24 incandescent bulb is 500 working hours, however our T5 24 27 LED bulbs in comparison is starting from 2, 000 up to 20, 000 operating hours.

         

 

For more information about 24 LED bulbs and 27 LED bulbs, please visit our website LEDoption.com

Ford explorer with LED Interior Lights Installation

Hi everyone. I planned to present everyone how to change those regular interior light bulbs for LED bulbs on 4th Gen Ford Explorer. I'm not sure if another person has or not posted this before, but here you go. I did the following on my 2007 Ford Explorer yesterday afternoon. This challenge required about 30-45 minutes to do. I am not responsible for any kind of injury YOU do to ones vehicle. Try this set up AT YOUR OWN RISK.

You are going to get 6 led bulbs. That is how much it needs for all interior bulbs. 3 sets of 2 bulbs per pack, hopefully I said this right with free shipping and delivery. I consider is a good deal. You are going to have some simple hand tools.

First factor is to get rid of screw from over head console.

As soon as you take remove screw, you will have to pop down front over head console, very carefully.

Simply planned to show everyone what contains the front part of over head console. After that you unplug connector to the lights.

Take off the 4 screws in the circle. Sorry for the picture, I didn't remember to take picture of product above flip over. (The 3rd photo indicates a better view of portion with screws)
(At least it illustrates the perspective of the standard bulb fitted. )

Graphic displays the LED bulb mounted. You might have to change (by turn them) them after you mount the overhead console, at least temporary.

I plugged them up to test them out. I think they are bright. (Turn on the LED bulbs, to view if they work. If one among them doesn't work, you may need to flip the bulb around. )

For the reinstalling the stuff is reverse of removal.

Here are some pictures previously mounted.

We found this helpful information from explorerforum.com and to get LED bulbs, please visit us at www.LEDoption.com, the affordable car LED store.

LED Panel Lights Installation for Dodge Charger

The lights that i ordered are not the exact measurement as the halogen bulbs that come stock. The do come with connections for both the front and the back so for $25 you might do your complete inner surface. Not bad if you ask me. For now just to make sure i liked them i ordered one set. $12. 50 shipped.

All right first off you have to have a small flat head screw driver. You will push this up by the portion of the light you push to change it on. Once you get it up pry it straight down. It will only fall a little, just like this particular.

When you get that done check out and you'll see a piece of plastic keeping it in. Take the tiny screw drive and push it up to the top of the plastic and push it in and pull down once you find it free. It will feel like its likely to break but unless you put an astronomical sum of pressure on it it won't. Couldn't truly get a picture of that.

As soon as you get the bit of plastic off you ought to take the old light out and get a set of two of pliers and pull the heat shields out. They're a little of a pain and i really just clamped down and jerked it. As soon as you have them out it should appear like the following.

Following that take your light and put it in the clamps. Just before you put the double sided tape down BE CERTAIN THE LIGHTS WORK! If they don't work at first try flipping it around in the clamp connections. I turned the lights entirely off when i was swapping it around. Didn't need to take the risk of receiving surprised or screwing something up. As soon as you observe that they are working Peel off the double sided tape and push it up there where it fits. I discovered it fits effectively and appears beneficial right here..

Check to ensure that all is still working.

Right now tuck the wires up in the light cavity making sure they don't block the lighting.

Right now to put the bit of plastic back on you work backwards. Get started with the back and clip it in.

And then push the front in. You may possibly have to push the piece in a little bit. then boom you're fixed! (the right one wasn't stuck up difficult enough so it is resting on the plastic and appears a little bit interesting)

We found this useful details from chargerforums.com and to get LED lights, please visit us at www.LEDoption.com, the affordable auto LED store.